Arduino MKR1000 32-bit ARM WiFi - ABX00004 - Loose headers SAMD21 Cortex-M0+

Description

Arduino MKR1000 combines the functionality of the Zero and the Wi-Fi Shield. This is an ideal board for makers that want to design IoT projects with minimal previous experience in networking.
Warning: Unlike most Arduino & Genuino boards, the MKR1000 runs at 3.3V. The maximum voltage that the I/O pins can tolerate is 3.3V. Applying voltages higher than 3.3V to any I/O pin could damage the board. While output to 5V digital devices is possible, bidirectional communication with 5V devices needs proper level shifting.
ABX00004 with loose headers ( not soldered ).
Arduino MKR1000 has been designed to offer a practical and cost effective solution for makers seeking to add Wi-Fi connectivity to their projects with minimal previous experience in networking.It is based on the Atmel
ATSAMW25
SoC (System on Chip), that is part of the SmartConnect family of Atmel Wireless devices, specifically designed for IoT projects and devices.
The ATSAMW25 is composed of three main blocks:
-SAMD21 Cortex-M0+ 32bit low power ARM MCU
-WINC1500 low power 2.4GHz IEEE® 802.11 b/g/n Wi-Fi
-ECC508 CryptoAuthentication
The ATSAMW25 includes also a single 1x1 stream PCB Antenna. The design includes a Li-Po charging circuit that allows the Arduino/Genuino MKR1000 to run on battery power or external 5V, charging the Li-Po battery while running on external power. Switching from one source to the other is done automatically. A good 32 bit computational power similar to the Zero board, the usual rich set of I/O interfaces, low power Wi-Fi with a Cryptochip for secure communication, and the ease of use of the Arduino Software (IDE) for code development and programming.
All of these features make this board the preferred choice for the emerging IoT battery-powered projects in a compact form factor.The USB port can be used to supply power (5V) to the board.The Arduino MKR1000 is able to run with or without the Li-Po battery connected and has limited power consumption. The MKR1000 Wifi module supports certificate SHA-256.
The Arduino MKR1000 combines the functionality of the Zero and the Wi-Fi Shield. This is an ideal board for makers that want to design IoT projects with minimal previous experience in networking. It features the Atmel ATSAMW25 SoC that is part of the SmartConnect family of Atmel Wireless devices that are specifically designed for IoT projects and devices.
The ATSAMW25 is composed of three main blocks; The SAMD21 Cortex-M0+ 32-bit low power ARM MCU, the WINC1500 low power 2.4 GHz IEEE 802.11 b/g/n Wi-Fi, and the ECC508 CryptoAuthentication. The MKR1000 includes a Li-Po charging circuit that allows it to run on battery power or external 5V charging the Li-Po battery while running on external power, where switching sources is automatically done.
It has similar computation to the Zero board, rich set of I/O interfaces, low power Wi-Fi with a Cryptochip for secure communication and ease of use of the Arduino Software (IDE) for code development and programming, making all these features the preferred choice for IoT battery-powered projects in a compact form factor.
This version is the MKR1000 without soldered headers.
Specifications:
Microcontroller: SAMD21 Cortex-M0+ 32bit low power ARM MCU
Board Power Supply(USB/VIN): 5V
Supported Battery(*): Li-Po single cell, 3.7V, 700mAh minimum
Circuit Operating Voltage: 3.3V
Digital I/O Pins: 8
12 (0, 1, 2, 3, 4, 5, 6, 7, 8, 10, A3 - or 18 -, A4 -or 19)
UART: 1
SPI: 1
I2C: 1
Analog Input Pins: 7 (ADC 8/10/12-bit)
Analog Output Pins: 1 (DAC 10-bit)
External Interrupts: 8 (0, 1, 4, 5, 6, 7, 8, A1, -or 16-, A2 - or 17)
DC Current per I/O Pin: 7mA
Flash Memory: 256 KB
SRAM: 32 KB
EEPROM: None, See documentation
Clock Speed: 32.768 kHz (RTC), 48 MHz
LED_BUILTIN: 6
Full speed USB device and embedded host
Dimensions: 2.42"L x 0.98"W